I am glueing all parts of the Mini Sinbad, with cyano only. It is a easy process that needs some attention as the glue cures very quickly. I followed 3d-printz assembly guide and did not found any problem with it.

I painted wingtips, cockpit and canopy, and a filet on the fuselage using same colors as on the Eclipson EGW80. For the servos i reused support available with the Eclipson model, printed in LW-PLA.

I am still missing the motor and nose, waiting for this one to come and be sure it will fit in the small area. Otherwise i will used the pure glider nose version. Current weight without motor and ESC, receiver and battery is 331g.

As Colorfabb is claiming on his web site LW-PLA and LW-ASA are very light weight material for 3D print and thus allow to build light models.

The Sinbad will definitively be very light and i weighed each printed part.

Current total weight of all parts is 282 g. I will need to add 2 9g servos, one receiver, motor+esc and the 2S 300mAh lipo battery, and all links and rods with rudder and elevator. Final weight should be around 420/430g.

I managed to print all parts of the Sinbad in one and a half week, doing this every evening and 2 week ends. Here is summary in a table of all times required for each print.

Parts	File	Time
WingtipL	E3PROSKR_WingtipL_1_SALWPLA-0-33-025	0h33mn
WingL2	E3PROSKR_WingL_2_SALWPLA-3-51-025	3h51mn
WingL1	E3PROSKR_WingL_1_SALWPLA-4-46-025	4h46mn
WingcenterLFloater	E3PROSKR_WingCenter_L_Floater_SALWPLA-4-43-025	4h43mn
Wingjoiner Floater	E3PROSKR_Wingjoiner_Floater_SBLWASA-2-12-025	2h12mn
Flachenaufnahme Floater	E3PROSKR_Flachenaufnahme_Floater_SALWPLA-2-38-025	2h38mn
WingcenterRFloater	E3PROSKR_WingCenter_R_Floater_SALWPLA-4-43-025	4h43mn
WingR1	E3PROSKR_WingR_1_SALWPLA-4-45-025	4h45mn
WingR2	E3PROSKR_WingR_2_SALWPLA-3-51-025	3h51mn
WingtipR	E3PROSKR_WingtipR_SALWPLA-0-32-025	0h32mn
Fus1	E3PROSKR_Fus1_SALWPLA-0-43-025	0h43mn
Motornose	E3PROSKR_Motornose_SCLWPLA-0-41-025	0h41mn
Motorspant	E3PROSKR_Motorspant_SBLWASA-0-27-025	0h27mn
Fus2	E3PROSKR_Fus2_SCLWPLA-4-57-025	4h57mn
Canopy	E3PROSKR_Canopy_SCLWPLA-0-57-025	0h57mn
Cockpit	E3PROSKR_Cockpit_SCLWPLA-1-14-025	1h14mn
Fus3	E3PROSKR_Fus3_SALWPLA-7-35-025	7h35mn
Fus4	E3PROSKR_Fus4_SCLWPLA-2-40-025	2h40mn
VertStab	E3PROSKR_VertStab_remix_bas_SCLWPLA-1-17-025 E3PROSKR_VertStab_remix_haut_SCLWPLA-0-53-025	1h17mn + 0h53
HorStabtop	E3PROSKR_HorStabTop_SALWPLA-0-14-025	0h14mn
HorStabL2	E3PROSKR_HorStab_L_2_SCLWPLA-1-15-025	1h15mn
HorStabL1	E3PROSKR_HorStab_L_1_SCLWPLA-1-42-025	1h42mn
HorStabR1	E3PROSKR_HorStab_R_1_SCLWPLA-1-41-025	1h41mn
HorStabR2	E3PROSKR_HorStab_R_2_SCLWPLA-1-15-025	1h15mn

Total print time of all parts is 60 hours and a few minutes.

Here is a photos gallery of all these elements

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

The full kit is ready to glue and being equiped with servos and motor.